• 목록
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

• 페이스북 공유
• 트위터 공유

Reasons Your fiat punto remote key replacement 500 Key Fob Won't Work

A key fob for the fiat ducato key programming 500 makes it easy to open doors and start your car. There are a myriad of reasons the key fob might stop working. These include a dead battery damaged receiver module, water damage issues, and interference.

This listing is for a NEW fiat doblo replacement key fiat keys Flip Key Remote - similar to the Ilco brand that must be professionally programmed by a local locksmith (click here to search for a Locksmith Search). It comes with lock, unlock and trunk buttons.

Dead Coin Battery

The most frequent reason that your 500 key fob will not function is the battery is dead. Key fobs of today have only a limited range of operation and must be within a few inches of your vehicle in order to work. If you're far away from your vehicle and press the key fob button the car will not respond, and will display the "Key Fob Not Detected" message in the instrument cluster.

If this happens then replace the battery for your coin-cell (Part Number CR2032) with a new battery from a reputable brand like Panasonic Duracell or Energizer. You can find them at your local hardware store, or on the internet.

You can test the coin-cell battery by pressing the buttons while standing close to your fiat 500 key cover 500. The car will flash its parking lights and the key fob should be able to operate the lock and unlock switches.

If the fob's remote doesn't function after replacing the battery, it might be damaged by water, which prevents it from communicating with the receiver module inside your vehicle. Water damage can happen in a number of ways, from small splashes to submerging the fob in salt water at the beach. If you suspect that your fob was exposed to water, you can place it in a bag of rice to draw out the moisture. If this doesn't work your fob may need to be reset by an experienced locksmith or dealer.

Water Damage

Damage to the water supply can occur if you submerge the fob in the ocean, or wash it in a washing machine. Saltwater poses a particular risk to the circuit board of the fob and can cause it to short out and eventually end up dying. It's not a good idea to submerge the fob in water however, but don't give it up even if you accidentally drop the fob in water, or fail to remove it from your pants pocket.

Take the battery off first. Clean the electronic chip with isopropyl ethanol or a similar product and dry it thoroughly before replacing the battery. Then check the fob to see if it works. If the key still doesn't function, it may need to be reset. This is typically handled by a dealer or professional auto locksmith.

If your key is older and not programmed for your car it is necessary to replace it completely. This is a straightforward process that can be completed by a professional locksmith for automotive use. The locksmith will need the key to be cut to match your vehicle's ignition. They'll also need to reprogram the fob for your vehicle's system. This is a simple and cost-effective process that can usually be completed within the same day.

Receiver Module Issues

One of the most common reasons your 500 key fob won't be functioning is because it's out of range. The remote usually has a range of 30 feet or less, and if it's too far away from your car it won't respond to your commands. It's easy to solve this problem by moving the remote closer to your vehicle until it responds.

If your fob does not work after you replace the coin battery, also called a "button", "watch" or "button" it may be due to a malfunction on the circuit board inside. Reprogramming your fob can resolve this problem. You can find directions on how to do this for the majority of automobiles by searching YouTube or reading the owner's manual.

You may need to replace the metal clips that keep the coin battery. If they lose tension, it can prevent your coin battery from sitting properly and cause your remote to malfunction.

In rare cases it is possible that the fob will become disconnected from your vehicle due to software issues or hardware issues. You can fix this problem by visiting your local auto-locksmith or dealer to reprogram your key fob. In certain instances the software may require reinstallation in your body control modules.

Interference

In addition to a dead battery on a coin The key fob might not be able to transmit or receive a signal due to interference. This could happen when the key fob is in close proximity to a radio transmitter like a cell phone or radar detector. The key fob could not work due to a poor connection with the buttons, water damage or damage to the internal chips.

If the key fob has been unable to function for a while without notice or after trying everything you can do at home to resolve it e.g. It could be a defective 500 receiver module if you've tried replacing the battery, reprogramming it, or using an alternative key fob. The receiver module is situated under the dash and is able to pick up the radio frequency signals from the key fob. Then, it converts them into electronic commands that the vehicle interprets.

There's a simple method to reset the 500's onboard system, including the keyfob. Disconnect the battery of 12 volts for about 15 minutes by taking off the negative cable first then the positive cable. Then reconnect the battery. This will eliminate any remaining electrical charge and restart the car's computers. This could help get your key fob working again. If the issue continues you should speak with a certified technician. They'll be able identify the root cause of your issue.