• 목록
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

• 페이스북 공유
• 트위터 공유

UPVC Replacement Door Handles

As time passes the handles on your doors will get worn out and will require replacement. It is important to be able to match the dimensions of the handles you have previously replaced when replacing them.

The top screw's location, the lever and the keyhole size are the three measurements you have to determine. Use the size guide to aid you.

Inline Lever/Lever

A lever/lever door handle is a modern handle that can be used on new or replacement doors. This kind door handle is available in a variety of styles & finishes. This handle is available from several manufacturers, including Avocet ERA Fullex Hoppe Mila Millenco Yale.

Fab and Fix Windsor Inline Sprung Lever Door Handle

The uPVC/Composite door handles are made of robust materials and are suitable for doors with multi-point locks which require a robust design. The handles are inline and work off the same spindle and screw fixings. They are easily installed on doors made of uPVC/Composite, either new or old.

The sprung lever design allows the handle to be positioned and angled to ensure a comfortable experience and is suitable for all users. The handle has been tested for endurance up to 200,000 cycles, this helps to ensure the quality of the finish as well as the performance of the handle over time. The lever that is sprung can be reduced to accommodate more locks. This is especially useful in doors with smaller door frames where the cylinder is located further back. A shortened lever is also an excellent option for doors where the latch could be opened by a thumb turn on the inside.

Lever Pad

The lever pad upvc handle is different from the lever handles that are commonly found on doors. These handle types can either use a single spindle (inline) or independently from each side by using two inline or offset spindles (pad). They are typically used on UPVC double glazed doors and come in a variety of styles and finishes.

The handles are available in a variety of finishes, including White chrome, and Gold. The finish meets BS EN 1670:2007 Grade 5 and is also resistant to corrosion, which gives the handle a high degree of durability and performance for the intended use.

All UPVC levers for handles come with a spindle, screws and can be mounted on a uPVC door. The backplate fixation centres of 211mm allow for a wider handle, which is usually beneficial when replacing a damaged or old multi-point door lock mechanism. The levers for these handles have springs, which eliminate the problem of handles for doors that slide out of their horizontal position when they are not being used.

When choosing the replacement UPVC handle and spindle it is essential to match the dimensions of the PZ on both the multipoint lock and the uPVC door. This measurement is also known as the 'handle centre' or 'cylinder centres and is an essential aspect of matching up the right handles.

After you have determined the correct PZ size, you will need to ensure that the push and lever pads are designed to fit the American with Disabilities Act compliant handles you require for your door. They are usually rectangular or round in shape, with an internal lever as well as an external push pad.

The majority of UPVC lever pads that we sell are sprung, meaning that they return to their horizontal position after not in use, rather than hanging out and potentially sticking in the frame. This stops draughts and cold air from entering a home. It is also the case that the majority of UPVC handle lever pad style replace window handles are hand-operated, allowing you to install them on either side of the door handles victorian.

euro lock handles Cylinder

Cylinder locks are found on uPVC and other types of doors. They work by using a key to unlock a cylinder case which then reveals pins which can be aligned with the pins in the lock body, allow them to rotate a revolving cam, thus opening the door. Euro cylinders can be equipped with up to six pins, with both internal and external doors usually requiring different levels of security.

The selection of a cylinder is essential. It's dependent on the type of use your doors and handles receive. External doors, for instance are required to be fitted with cylinders that are more secure, whereas internal doors can be secured using an ordinary cylinder. In addition, some cylinders are available with extra features that can improve security further, such as anti-drill or anti-bump properties.

A euro cylinder should be properly measured to ensure it is the right size for your door. The cylinder must be measured from the screw hole in the center to the ends of the cylinder. This includes the thumb turn, in the event that one is present. If you are unable measure it using the lock in a fixed position, you can remove it. A cylinder that extends beyond the handle and escutcheon may be vulnerable to attacks, such as lock snapping, so it is important to make sure it's not too long.

The design of the latest cylinders comes with anti-drilling as well as bump resistance features. They are designed to decrease the chances of an attack by causing the cylinder to rotate in a different direction. This can deflect the attack, and keep your door safe.

Some cylinders are designed to resist snapping. This is a typical attack on cylinders. A specific tool is used to break the break line of the lock, and the front of the cylinder is snapped off. This is a much faster and more convenient method of gaining access than through the use of a multipoint locking system. It also leaves less evidence of the break-in which could make it difficult to prove insurance claims.

Spring Cassette

This spring cassette is located in the base plate of the door handle. It offers a spring-loaded solution to help return your multipoint lock handles back to their original position after using. In the past, a lot of these types of handle did not have a spring built into them, and as a result, they can droop or drop when the locking mechanism is disengaged. This simple feature is one of the best methods to correct this issue and is an excellent way to stop your doors made of upvc from becoming stuck in either closed or open position, since they are not always easy to close manually.

These spring cassettes have been specifically made for use with sprung multipoint locks but they won't work with multipoint handles that are not sprung and you must have a custom hole cut into your backplate in order for them to fit (please check the image for a technical diagram). They are a replacement for existing damaged or missing cassettes inside the backplates of door handles of various kinds of uPVC doors. They are available as one unit. They have a square-cut out that is able to accommodate an 8mm shaft.

These spring cassettes provide a great value solution to the problem of door handles that have become sagging. They are simple to put in and will extend the lifespan of your uPVC doors. Contact us for more information on our selection of uPVC accessories and spares. We are here to assist and give you expert advice.